Brass Stacker - SKS See Thru Scout Scope Mount - Russian 45

See Thru SKS Scout Scope Mount by Brass Stacker

Scope your SKS while preserving its historic integrity.

"ANCHOR POINT" Series - See Through Design

• Innovative “Anchor Point” design provides superior mount stability
• See-thru design for continued use of fixed iron sights
• No permanent modification of firearm required*
• Allows for complete field stripping without mount removal*
• Will not interfere with stripper clip use*
• Does not contact stock
• Casing Deflector available for long tube optics
• Rigid all steel construction, includes 5/16” x 3-5/16” Picatinny Rail
• Cross bolt nut spanner wrench is included
• Unit comes loosely preassembled
• Made in America with a 100% Lifetime Warranty

*Please note certain restrictions as follows: Mount for use with original wooden stocks or TAPCO synthetic stocks ONLY. ***Cross bolt drill templates for TAPCO stocks are not yet available but will be available soon.*** It will NOT work with ATI® or ANY OTHER synthetic stocks. Permanent modification of stock IS required for use with TAPCO synthetic stock. Lack of “interference” applies to “mount” only. Optic interference (with disassembly of the gas tube or use of stripper clip) may occur depending on the optic type, optic length/diameter, ring height, etc. Compact, red dot or reflex type optics can typically be positioned avoiding any interference. Stripper clips CANNOT be used in conjunction with Casing Deflector. PLEASE READ FITMENT NOTES BEFORE PURCHASING! If you intend to use a long tube optic, the Casing Deflector (model # SKSCD) is highly recommended.

FEATURES: Product provides for the mounting of scout scope, red dot/reflex type or other long eye relief (LER) optics to SKS rifles without the need to drill and tap the receiver or make any permanent modifications to firearm. It is designed to use the cross bolt (sometimes referred to as the recoil lug) as the primary attachment point and securely installs over rear sight block.

FITS:

• Russian 45
• Chinese Type 56 (Non-Norinco)
• Yugoslavian 59/66

Unit is shipped with a variant specific cross bolt.

SPECIFICATIONS: The mount will accommodate a front to back (horizontal) distance of approximately 1-5/8" to 1-3/4" from the center of the cross bolt to the center of the rear sight block ladder pivot. It also allows for an up and down (vertical) distance of approximately 1-9/16" to 1-15/16" from the same. The total weight mount, picatinny rail and hardware is 5.8 oz. However, the net weight increase is only 5.5 oz. due to the replacement of the original cross bolt and nut.

UNIT: Mount: 1) CNC laser cut perimeter, die punched holes and mounting slots, form tapped threads and die press formed. 1/8" (11 ga.) thick HR, P&O type CS-B A569 carbon steel; 40000 psi yield strength. Black oxide plated. Picatinny Rail: 1) CNC machined to MIL-STD-1913, 3-5/16" long, HR ATSM A36 low carbon steel; 36000 psi yield strength. Black oxide plated. Cross Bolt: 1) 12L14 alloy steel. Black oxide plated. Spanner Nuts: 2) 12L14 alloy steel. Black oxide plated.

HARDWARE: Set Screws: 2)#10-32 x 1, 2)#6-32 x 3/4", 3)#3-48 x 5/16". Lock Washers: 2)#10 Ext tooth, 2)#10 Int tooth, 2)#6 Ext tooth, 2)#6 Int tooth. Flat Washers: 2)#10, 2)#6. Shims: 4) 7/16" x 5/16" x 1/32". Nuts: 2)#10-32 Hex, 2)#6-32 Hex.

TOOLS PROVIDED: Wrench: 1) 3/32" Hex wrench - steel; 1) 1/16" Hex wrench - steel; 1) .050 Hex wrench - steel; 1) 1/2" Hex body cross bolt nut spanner wrench - steel, black oxide finish; Complete installation instructions are supplied.

SCOPE & RINGS ARE NOT PROVIDED!

FITMENT NOTES:

We have made every reasonable effort to ensure that this product will fit the majority of SKS rifle variants (Russian 45, Chinese Type 56 [non Norinco], Yugoslavian 59/66, etc.). However, due to the large number of these firearms produced over many years around the world, it is impossible for us to allow for all manufacturing variation. This mount will NOT work for NORINCO/CSI SKS's. We are actively working to make that accommodation. As with any of our products, it may be returned undamaged for a full refund. Proper tightening of all hardware should result in no movement of the mount during normal firing recoil.

TOOLS REQUIRED:

Safety glasses, solid work surface or vise, 3/8" hex wrench, 5/16" hex wrench, hammer and punch. A 9/32" drill is required for installation in TAPCO synthetic stock.

NOTE:

Any scope and/or mount that suffers an impact, should not be trusted to be accurate. If you feel your mount has been compromised, you can still use your original open iron sights. Design subject to change without prior notice.

Caution! Improper installation or use may result in damage to property, severe injury, or loss of life. If for any reason this product does not function properly, discontinue use immediately. Always practice proper SAFETY and ensure an UNLOADED condition before beginning installation.